DOC022.52.00630JUN04PORTABLE TURBIDIMETERModel 2100P ISOInstrument manual© Hach Company, 2004. All rights reserved. Original: bb 6/04 4ed
Page 10SPECIFICATIONS4650098 specs.fmSPECIFICATIONS, continuedStorage Temperature: –40 to 60 °C (instrument only)Operating Temperature: 0 to 50 °C (in
Page 114650098 opstop.fmDANGERHandling chemical samples, standards, and reagents can be dangerous. Review the necessary Material Safety Data Sheets an
Page 124650098 opstop.fm
Page 134650098 intro.fm DescriptionSection 1 Description 1.1 General DescriptionThe Hach Model 2100P ISO Portable Turbidimeter (Figure 1) measures tur
Page 14Preparation for Use4650098 intro.fmSection 1, continuedratio of the signals from the 90° and transmitted light detector. This ratio technique c
Section 1, continuedPage 154650098 intro.fm Preparation for UseFigure 3 Battery Installation1.4.2 Using the Battery Eliminator and Rechargeable Batter
Page 16Preparation for Use4650098 intro.fmSection 1, continued
Page 174650098 operation.fm OPERATIONSection 2 OPERATION2.1 Operational Controls and IndicatorsKey DescriptionPower key turns instrument on and off. I
Page 18Signal Averaging4650098 operation.fmSection 2, continued2.2 Signal Averaging Signal averaging measures and averages ten measurements while disp
Section 2, continuedPage 194650098 operation.fm Calibrationduring measurement, the initial value is displayed in 12 seconds and is updated every 1.2 s
http://www.hach.com
Page 20Calibration4650098 operation.fmSection 2, continued• Store away from direct sunlight. Store vials in their respective kit or shipping box with
Section 2, continuedPage 214650098 operation.fm Calibration2.3.2 Correcting for Turbidity of Dilution WaterThe 2100P ISO Turbidimeter automatically co
Page 22Calibration4650098 operation.fmSection 2, continued• To review a calibration, press CAL and then × to view the calibration standard values. As
Section 2, continuedPage 234650098 operation.fm Calibration7. The display will show “S1” (with the 1 flashing) and 20 FNU or the value of the S1 stand
Page 24Calibration4650098 operation.fmSection 2, continued17. Press READ. The instrument will count from 60 to 0 (67 to 0 if signal average is on). Th
Page 254650098 measure.fm TURBIDITY MEASURESection 3 TURBIDITY MEASURE3.1 Turbidity MeasurementMeasurements may be made with the signal average mode o
Page 26Turbidity Measurement4650098 measure.fmSection 3, continued5. Wipe off the excess so that only a thin coat of oil is left. Excess oil may retai
Page 274650098 mainstop.fm MAINTENANCESome of the following manual sections contain information in the form of warnings, cautions and notes that requi
Page 28MAINTENANCE4650098 mainstop.fm
Page 294650098 maintenance.fm MAINTENANCESection 4 MAINTENANCE 4.1 Lamp Replacement The procedure below explains lamp installation and electrical conn
Page 34650098 GBTOC.fmTABLE OF CONTENTSCERTIFICATION ...
Page 30TROUBLE SHOOTING4650098 diagnostics.fmSection 5 TROUBLE SHOOTING5.1 Instrument Diagnostics5.1.1 Display TestPressing and holding the I/O key tu
Section 5, continuedPage 314650098 diagnostics.fm Error MessagesMessage Probable Cause Corrective ActionE1Dilution water is ≥ 0,5 FNU. Start calibrati
Page 32Replacement Parts & Accessories4650098 parts.fmReplacement Parts & AccessoriesREPLACEMENT PARTSDescription Cat. No.AA Batteries, 4/pkg
, continuedPage 334650098 parts.fm Replacement Parts & AccessoriesStablCal® Calibration Set for 2100P ISO Turbidimeter<0.1, 20, 100, 800 FNU, 5
Page 34HOW TO ORDER4650098 end.fmHOW TO ORDERInformation RequiredIn Europe, the Middle East, or Mediterranean Africa:Dr. Bruno Lange GmbH & Co KGW
Page 354650098 end.fm REPAIR SERVICEREPAIR SERVICEAuthorization must be obtained from Hach Company before sending any items for repair. Please contact
Page 36WARRANTY4650098 end.fmWARRANTYHach Company warrants this product to the original purchaser against any defects that are due to faulty material
, continuedPage 374650098 end.fm WARRANTYThis warranty contains the sole express warranty made by Hach Company in connection with its products. All i
Page 44650098 GBTOC.fmTable of contents, continuedSection 5 TROUBLE SHOOTING ...30
Page 54650098 cert.fmCERTIFICATIONHach Company certifies this instrument was tested thoroughly, inspected and found to meet its published specificatio
Page 64650098 cert.fmCertification, continuedEmissionsInstrument Tested with the external 230 V, 50 Hz Power Supply:Per 89/336/EEC EMC: EN 61326:1998
Certification, continuedPage 74650098 cert.fmThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
Page 8SAFETY PRECAUTIONS4650098 safety.fmSAFETY PRECAUTIONSPlease read this entire manual before unpacking, setting up, or operating this instru-ment.
Page 94650098 specs.fm SPECIFICATIONSSPECIFICATIONSSpecifications are subject to change without notice. Operating specifications applicable at 25 °C u
Comments to this Manuals