DOC023.52.90171TSS EX1 sc User Manual07/2013, Edition 5ATurbidity and Solid matter sensor TSS EX1 sc II 2G Ex d IIC T6 Gb Ta = –10 to 50 °C II 2D Ex
10General information
11Section 3InstallationNote: Depending on the area of application, the sensor may have to be installed with additional optional accessories 3.1 Instal
12Installation3.2 Installation sensor pipe installation option Figure 4 Installation options3.3 Grounding3.4 Connect the sensor cable1. Unscrew the pr
13InstallationFigure 5 Connect the sensor plug to the sc controllerFigure 6 Pin assignment3.4.1 Cable extension with terminal box LZY586 Use for cable
14Installation
151515Section 4 Operation4.1 sc controller operationThe sensor can be operated with all sc controllers. Become familiar with the functionality of the
16Operation16Operation16Operation4.4 Menu structureNote: Refer to Section 6 Malfunctions, causes, resolution for a list of all error and warning messa
17Operation17Operation17OperationOUTPUT MODE Behavior of the outputs during calibration or while the zero point is being setHOLDACTIVETRANSFERSELECTIO
18Operation18Operation18Operation4.5 CALIBRATENote: Turbidity measurement has been calibrated by the manufacturer — it does not need to be calibrated
19Operation19Operation19OperationAt least a 1-point calibration must be carried out for a solid matter measurement. In difficult application condition
20Operation20Operation20Operation4. Press CALIBRATE and confirm.5. Press CALIBRATE and confirm.6. Press RECORD and confirm.7. Press POINT... (point 1,
21Operation21Operation21Operation4.5.2.3 1 to 3 point calibrationNote: It is imperative to calibrate for solid matter measurement (refer to section 4.
22Operation22Operation22Operation5. Press CALIBRATE and confirm.A mark "<<" is displayed after the recorded point or points for approx
23Section 5 MaintenanceThe cleanliness of the measurement windows in the sensor head is decisive for the accuracy of the measurement results!Check the
24Maintenance
25Section 6 Malfunctions, causes, resolution6.1 Error messagesPossible sensor error messages are displayed by the sc controller.6.2 Warning messagesPo
26Malfunctions, causes, resolution
27Section 7 Replacement parts and accessories 7.1 Replacement partsDescription Catalog numberManual (xx = language code) DOC023.xx.901717.2 Accessor
28Replacement parts and accessories
29Section 8 Contact information HACH Company World HeadquartersP.O. Box 389 Loveland, Colorado 80539-0389 U.S.A. Tel (800) 227-HACH (800) -227-4224 (U
3Table of contentsSection 1 Specifications ...
30Contact informationHACH LANGE D.O.O.Fajfarjeva 15 SI-1230 Domžale Tel. +386 (0)59 051 000 Fax +386 (0)59 051 010 [email protected] www.hach-lange.s
31Section 9 Warranty and liabilityThe manufacturer warrants that the product supplied is free of material and manufacturing defects and undertakes the
32Warranty and liability
33Appendix A Modbus register Table 3 Sensor modBUS registers Tag Name Group Name Register Data Type Length R/W DescriptionTURBIDITY FNU Measurement 4
34Modbus registerFormatMinPR Configuration 40071 Float 2 R Solid Lower Limit in PercentFormatMaxPR Configuration 40073 Float 2 R Solid Upper Limit in
35IndexAAreas of application ... 8CCable length ...
36Index
4Table of contents5.2 Clean the measurement windows ...
5Section 1 SpecificationsSpecifications are subject to change without notice. MeasurementMeasurement methodCombined multiple-beam alternating light t
6Specifications1.1 DimensionsFigure 1 DimensionsMiscellaneousInspection interval upon request 1/year service contract with warranty extension to 5 yea
7Section 2 General information2.1 Safety informationPlease read this entire manual before unpacking, setting up, or operating this equipment. Pay atte
8General information2.1.2 Warning labelsRead all labels and tags attached to the instrument. Failure to do so may result in personal injury or damage
9General informationUp to three calibration points can be defined for a strongly fluctuating medium. The combined multiple-beam alternating light tech
Comments to this Manuals